SCANALOGIC
2
| Logic
Analyzer & Signal Generator |
Home-Made
KIT
Last update:
11/3/11
|
 |
Introduction
 |
SCANALOGIC-2 PRO can be built
at home allowing you to reduce total costs, and have fun building
your device!
SCANALOGIC-2 is all SMD components, so the home-made KIT it's
not for the absolute beginners. However, all the components are
chosen so that it's doable at home, without needing any expensive
material. You just need a sharp soldering iron, some skills and
some patience!
Testimonials
|
To encourage you to build your own SCANALOGIC-2,
here is a quote from Michael Urban, from germany,
who build his own SCANALOGIC-2 PRO device:
|
"Soldering
all the SMD parts to the two-sided PCB is challenging, but
nothing that can't be handled with a little SMD soldering
practice. Assembly instructions consist of a component placement
drawing and a list of components - very easy to work from.
While
it probably isn't the big money saver to build the SCANALOGIC2
instead of buying the completed device, it certainly is
fun and gives you a good feeling of it now being "your"
device.
Greetings,
Michael " |
Here is anoter quote from Julian Vogel, from
germany too.
|
"Thank
you very much for answer my question. Yesterday the expected
delivery closely arrived and after assembly the device works
lovely.
Your company did a great job with the Scanalogic 2!
Yours sincerely,
Julian Vogel"
|
When correctly mounted, the home-made (DIY) version
of SCANALOGIC-2 KIT will have the exact same features
of the ready-assembled PROversion.
|
Schematic
|
Below is the schematic of SCANALOGIC-2. Although you don't need
it to build the Home-Made KIT, it can be interesting to see how
Scanalogic-2 actually works.
(click on picture to download PDF) |
Below is the list of the components required (included in the
KIT)
Components list:
C2,
C5 |
10nF (1206
package) |
IC1 |
ATMEGA168-20A 
(not needed, provided with the PCB) |
IC2 |
SN74LVC1G125DCKR |
JP1 |
(for factory testing
only) |
JP2 |
2.54mm 5P connector for
the probes |
LED3 |
CMS LED (1206 package)
|
Q4 |
20 MHz oscillator
|
R1 |
100
(1206 package) |
R3 |
1M
(1206 package) |
R11 |
1K
(1206 package) |
U1,U2,U3,U4 |
23K256 |
U5 |
LP2985IM5-3.6 |
X1 |
USB connector |
C1,C3,C4 |
22µF (1206 package) |
DZ1,DZ2 |
Zener diode 3V6
|
IC3,IC4 |
74LCX125M |
R2, R12 |
1.5 K
(1206 and 0603 packages) |
R4, R5 |
~ 56
(1206 package) |
R6,R7,R8,R9,R10 |
1K
(1206 package) |
| RN1 |
100K (4 elements resistor network) |
Components implantation
|
Top Face components:
(click on picture to enlarge) |
Bottom Face components:
(click on picture to enlarge) |
Get
your SCANALOGIC-2 KIT now!
|
|
49€
SCANALOGIC-2 KIT.
If you want to save some money and have
fun soldering the components yourseff, this complete KIT
is for you! It comes with a high quality PCB with the
micro-controller soldered and pre-programmed, so you don't
need a programmer to make it work, just some surface mounted
soldering skills.
This
KIT ships with Probes, USB cable, PCB,
and ALL components needed to build your own device. |
If you have any questions, or face any problems while assembling
your KIT, you can always
contact us by mail, phone or FAX.
Browse SCANALOGIC 2 pages:
|
